Solar and Grid Hybrid System

Key Fetures:

Specification:

Series No.		GSHY- 300W	GSHY- 500W	GSHY- 1000W	GSHY- 2000W	GSHY- 3000W	GSHY- 4000W	GSHY- 5000W
Power Output	DC output	12V 5W Interface, 5V/0.5AUSB
	Rated Power(AC)	300w	500w	1000w	2000w	3000w	4000w	5000w
	Peak power(AC)	600w	1000w	2000w	4000w	6000w	8000w	10000w
	Voltage/ Frequency	100V/110V/120V/200V/220V/240V (±5%), Pure Sine Wave 50Hz/60Hz (±0.5Hz), Single phase
Power Input	Battery voltage	24V	24V	48V	48V	48V	48V	48V
Power Input	Grid voltage /Frequency	100V/110V/120V/200V/220V/240V 50Hz/60Hz (±0.5Hz), Single phase
Component and Specification
Poly Solar Panel (standard)		155w/18v	310w/36v	310w/36v	310w/36v	310w/36v	310w/36v	310w/36v
Poly Solar Panel (standard)		4pcs	4pcs	8pcs	16pcs	24pcs	28pcs	32pcs
Battery(GEL) 12V (optional)		100Ah	200Ah	200Ah	200Ah	200Ah	200Ah	200Ah
Battery(GEL) 12V (optional)		2pcs	2pcs	4pcs	8pcs	12pcs	16pcs	20pcs
Combiner box(standard) (IN/OUT)		No	4/1	4/1	8/1	12/1	14/1	16/1
AC charger(optional)		1pc	1pc	1pc	1pc	1pc	1pc	1pc
Bracket(optional)		1set	1set	1set	1set	1set	1set	1set
DC switcher(optional)		2pc	2pc	2pc	3pc	4pc	5pc	6pc
AC switcher(optional)		1pc	1pc	1pc	1pc	1pc	1pc	1pc
Function /Working Conditions
Display		LCD , statue of system
Protection		Overload, battery over/under voltage, over current, over/under voltage recovery
Protection		High temperature, short circuit, Reverse connection
Communication		RS232
Cooling		Fan
Working temperature		-30℃ ~55℃
Warranty		1year

Connection Step:

1) Before installation and debugging to prepare the corresponding installation tools and measuring tools,

such as cross screw driver, diagonal cutting pliers, multi meter, etc.

2) Check whether the required parts is complete(wiring, accessory bag and user manual, etc.) or not,

PV panels’ and battery’s voltage match the inverter type,Batterycapacity must be able to provide enough

load current.

3) Before use ,the inverter’s ground(GND) must connected the earth, and can not be used to the zero line

of local Electric line.

4) Ensure that all the power switcher in OFF .

5) Confirm the positive and negative polarity of battery, high potential for positive(B+),low potential

Negative(B-).

6) Confirm the positive and negative polarity of PV panels, high potential for positive(S+), low potential

Negative(S-).

7) The input terminals of inverter with screwdriver respective unscrewing.

8) Choose an appropriate cross sectional area of the red wire one end(see table 1)connect the battery,

the other Side to connect Air-switcher(circuit breaker)(see table 2)input terminals, The air switch

(circuit breaker)’s output Terminal connect the inverter input terminals, The positive terminal B(+)

and by cross screw driver to tighten. To complete the positive terminal connection of the battery

( The steps ①as shown in figure 1).

9) Choose an appropriate cross sectional area of the black wire one end(see table 1) connect the

battery, the other Side to connect Air-switcher(circuit breaker)(see table 2)input terminals, the

air-switch(circuit breaker)’s output Terminal connect the inverter input terminals the positive

terminal(B-) and by cross screwdriver to tighten, to Complete the negative terminal connection of

the battery(the steps②as shown in figure 1).

Negative terminal(S-)( the steps④⑥as shown in figure 1) connection.

11) Repeat the same steps8) and 9) will connect the mains input AC-IN(Grid input) connection

terminals(outlet)(The steps⑦as shown in figure 1).

12) Load (no more than inverter’s rated power) connected to the AC output AC-OUT connection

terminals(outlet)(The steps ⑧as shown in figure 1).

13) Check the wiring connection and first close the battery Air switch(circuit breaker)(the K3 as shown

in figure1).Open the control part of the switch(press “ON” key)(The steps⑨as shown in figure 1),

then the LCD display Show the current battery voltage, PV panels’ charging current and grid’s

voltage and current. The inverter output Voltage /Frequency are shown for free. Close PV panels

Air switch((circuit breaker)(as shown in figure 1, K1,K2)will display the current charging current at

this time.

14) When the LCD show the battery’s voltage and other data are normal without warm, open the

inverter part switch(The steps⑩ as shown in figure 1), the grid charge indicator and grid indicator

will bright. After the battery full Charged, the mains full charge indicator will bright.

15) Open the load power switch of electrical equipment(press “ON” key) end.

16) When the system is not work, shut off the grid charge switch and then disconnect the grid input

terminals Air switch, and then disconnect PV panels’ air switch(circuit breaker), close control part

switch, disconnect the Batteryair switch.

Download:Solar and Grid Hybrid System

SOLAR CELL

SOLAR PANEL

SOLAR POWER SYSTEM

SOLAR LIGHT

SOLAR PUMP SYSTEM

REFRIGERATOR/FREEZER

WIND POWER SYSTEM

SPARE PARTS

SOLAR POWER DEVICE

Solar Charge Bag